Home Control Home Automation and Home Automation Control Manager are home automation systems, which provide complete automation and remote connectivity. Home Control Home Automation, the system The Home Control home automation system consists of: a central processing unit, which takes care of sending [...]
Control Casa and Control Manager are home automation and building automation systems, to provide high quality full automation and remote control. Home automation, plant schematic The home automation system is composed of: central processing unit that shares data with […]
DAT X2 is the new version of the control system for 3CTR tunnel lifting equipment. It is installed on three-arm lifters for tunnels: two baskets to lift the workers, as well as a central arm to lift the [...]
DAT X2 is the new version of 3CTR electronic control system for tunneling lifters. It is installed on 3 booms tunneling lifters: 2 platforms to lift workers and 1 central boom to lift centres in tunnels. Electronic proportional manipulators and […]
I carried out the jet DSP 100 project on behalf of DAT instruments. It is a small operator panel, equipped with a graphic monitor and keyboard consisting of only three buttons, with built-in datalogger. The JET DSP 100 measures and [...]
JET DSP 100 datalogger records several parameters depending on version and connected sensors: IR version, for Lugeon tests, Permeability tests, Grouting (pressure, flow-rate, volume, time, duration); D version, for Diaphragm walls and Hydromills (depth, speed, inclination, deviation, rotation, time, duration). […]
DAT CB programmable controllers are a set of programmable electronic boards. Many projects carried out by DAT instruments use these electronic boards. I started designing these programmable controllers in March of 2002 and, years later, this set [...]
DAT CB programmable controllers are a set of programmable boards. Many DAT instruments projects use these boards. I began designing these boards on March 2002 and the project is still active. There is a main controller (the DAT CB CPU […]
The JET 4000 AME project was developed to meet the needs of completeness and robustness. The JET 4000 AME is in fact a control panel and datalogger, full of functions, constantly updated over the years. The project was born in [...]
JET 4000 AME datalogger records several parameters depending on version and connected sensors: I version, for Lugeon tests, Permeability tests, Grouting, GIN (grouting intensity number) injections (pressure, flow, volume, time, duration); J version, for Drilling, Jet grouting, Soil mixing, CFA, […]
3CTR is a complete control system for tunnel lifts. It is installed on three-arm equipment: the tunnel installers. Thecentine posecents are, in essence, composed of two baskets for lifting people and an arm [...]
3CTR is a complete electronic control system for tunneling lifting equipment. It is installed on 3 booms lifting equipments for tunneling: 2 platforms to lift people and 1 central boom used to lift centres in tunnels. Electronic proportional manipulators complete […]
MPLEX is a project I had done as a boy to test integrated circuits and logic gates. The project consists of an interface, to be connected to the LPT port of the computer, and a software, programmed in QuickBasic, which works in the [...]
MPLEX was an interesting project that I used to inspect integrated circuits and logic ports. The project consisted of a LPT interface board, which was connected to the PC parallel port, and of a software running on QuickBasic.The first version of […]
CTRLIM is a moment limiter for cranes and telehandlers. The moment limiter stops the machine when the arm moment is greater than a set value. The moment is expressed in Newton * meter (Nm) and measures [...]
CTRLIM is a moment limiter for cranes. The moment limiter stops the crane when the moment on its boom is higher than a preset value. Moment is calculated by an angle sensor, a boom length sensor and a hydraulic pressure […]
LPTEL is a telephone ring repeater: it turns on a light bulb when the telephone is ringing. It connects to the telephone line, so it is independent of the telephone. Telephone ring repeater, components R1 – resistor 47 ohm 1/4 WC1 – […]
STROBO is the project of a xenon strobe lamp, which I made when I was a boy. The lamp can flash independently, at a setable frequency, and moreover it can also be controlled from the PC, a microphone and other lights, through modules [...]
STROBO is a xenon strobe light (stroboscopic light) that can flash automatically or it can be controlled by a PC, by other lights or by a microphone. Please note that the components are grid power supplied (230Vac), hence do not […]
SPTEL is a busy phone line detector, which I designed when I was just over 15 years old: it is an LED that lights up when the phone line is engaged by a telephone in conversation. This my [...]
EQUATIO is a software for graphs of mathematical functions, which plots the functions, in 2D, on a Cartesian X-Y plane. I programmed this software when I was 15 years old: on the other hand, at the Scientific High School, mathematical functions were studied. I then [...]
EQUATIO is a DOS math graphing software to trace 2D mathematical functions on a X-Y Cartesian plane. It is possible to write an expression for each Cartesian axis. The graph is traced point by point. Available mathematical functions in EQUATIO […]
I programmed, when I was a boy, this Multitask Editor, just to gain experience. It was not a real necessity: even at the beginning of the 90s there were text editors, and also very performing. For example, Microsoft Word for DOS was born in [...]
I programmed this Editor Multitask just for fun. It was not a real necessity, but I often was writing programs like editors or file managers, just to learn useful commands and to understand how the Computer works. Programming language: Microsoft […]
INDIRIZZ is a database, an archiving program, which I started programming in 1992, when I had not yet turned 15, and I updated until 1994. I created INDIRIZZ for personal and also corporate use (for the Italmec company). [...]
COM TRANSFER is an instant messaging software, which I programmed when I was 14 years old. The messaging program allows you to send messages between two computers that are not connected to the network, as it uses the RS232 serial port. I wrote the [...]
COMPILED is a vector drawing program that has engaged me for more than a year, since I was just over 14 years old. The goal of COMPILAT was not only to draw, but rather to have the possibility [...]
COMPILAT was a drawing software that I wrote in more than one year. The main purpose was not just to make drawings, but to have the possibility to use these drawings inside other programs and games I were programming at […]